_address


Attribute (neutral)	Type	Description
_active	bool	You can set the peripheral address active or inactive by using the attribute _address.._active. An inactive address exists and attributes can be set or queried but the driver does not use them. If the address is inactive, It is not possible to send values to the PLC or to receive them. A connection to the PLC is not built for this datapoint. Conflicts with other addresses are not checked.
_connection	string	Used by some drivers.
_datatype	int	Specifies the data type of the value in the periphery and determines the necessary type conversion (Transformation) of the value between WinCC OA and periphery. The meaning of the values is driver specific. See the tables further below.
_direction	int	Sets the input or output mode of the address. The different modes are described in the table peripheral address "_address.._direction" further below. The attribute represents the bits 0-4 of the _mode attribute.
_drv_ident	string	This attribute contains the driver type (for example "MODBUS" for the Modbus driver).
_internal	bool	Sets the internal bit. Possible values: TRUE/FALSE. This bit can be used to handle an address specially. Whether the address is used and how it is used, depends on the specific driver. This attribute represents the bit 5 of the _mode attribute.
_interval	time	Interval. Obsolete.
_lowlevel	bool	Sets the low level filter bit. Possible values: TRUE/FALSE. By using this bit, the low level Old/New comparison is activated or deactivated. This attribute presents the bit 6 of the _mode attribute.
_mode	char	This attribute contains the address mode. It combines the attributes _direction, _internal and _lowlevel. Thus, the attribute mode is replaced by the attributes _direction, _internal and _lowlevel.
_offset	uint16	This attribute is used for saving optional address information of the used driver.
_poll_group	dpid	This attribute contains the reference to a poll group. The polling parameters are defined in this poll group. Thus, the attributes _interval and _start are obsolete. See chapter Poll groups. Note that when creating poll groups it might be necessary to reopen the _address panel since the new poll group is not necessarily shown immediately. The poll group is only set if it is correctly specified by using the system name + data point name for the destination system. Otherwise the poll group is not displayed in the para either.
_reference	string	The reference string specifies the address of the data in the periphery. The format of the address string is driver specific. See for example Defining the peripheral addresses of the Modbus/TCP driver.
_start	time	Start time. This attribute is obsolete.
_subindex	uint16	The subindex allows you to access data of a peripheral address, for example, the individual bits in a 16Bit word.
_type	type	Type of the peripheral connection.

Constants for the ".._type" attribute


CTRL Constant	Int Value	Description
DPCONFIG_NONE	0	No peripheral address
DPCONFIG_PERIPH_ADDR_MAIN	16	General peripheral address

"_address.._datatype" peripheral address

In the following the integer constants of the transformation types for the different drivers are listed. These constants are set in the respective address panel of the driver and are then interpreted by the driver. This means that the driver executes the appropriate transformation.

BACnet


Transformation type	Integer	Description
DEFAULT	800	Default. The necessary transformation is determined automatically.
BOOLEAN	801	Boolean
UNSIGNED INTEGER	802	32-bit unsigned integer
SIGNED INTEGER	803	32-bit signed integer
REAL	804	32-bit floating point number
DOUBLE	805	64bit double precision floating point number
OCTETS	806	Byte string
STRING	807	Text string
BITSTRING	808	Bit string
ENUMERATED	809	Enumeration type
DATE	810	BACnet date
TIME	811	BACnet time
DATETIME	822	BACnet date time

DNP3


Transformation type	Integer	Description
ANALOGINPUT	210	Analog input
ANALOGOUTPUT	211	Analog output
BINARYINPUT	212	Binary output
BINARYCOMMAND	213	Command
COUNTER	214	Counter
ASSIGNCLASS	215	Assign class

EIP


Transformation type	Integer	Description
UNDEFINED	770	Undefined
INT16	771	16-bit Integer signed
INT32	772	32-bit Integer signed
UINT16	773	16-bit Integer unsigned
UINT32	774	32-bit Integer unsigned
CHAR	775	Character
FLOAT	776	Floating-point number
BIT	777	Bit
Bit in WORD	778	Bit of a 16Bit word
BIT in DWORD	779	Bit of a 32Bit word
STRING	780	String
BLOB	781	Blob

IEC


Transformation type	Integer	Description
UNDEFINED	520	Undefined
SIQ	521	Single point information with quality descriptor
DIQ	522	Double point information with quality descriptor
VTI	523	Value with transient state indication
NVA	524	Normalized value
SVA	525	Scaled value
R32	526	R32-IEEE, short floating point number
BCR	527	Binary counter reading
SEP	528	Single event of protection equipment
SPE	529	Start events of protection equipment
OCI	530	Output circuit information of protection equipment
BSI	531	Binary state information
SCO	532	Single command
DCO	533	Double command
RCO	534	Regulating step command
SCD	535	Status and status change detection
COI	536	Cause of initialization
PRIVAT	537	Private user data with application specific structure.
EMPTY	538	Transformation type for a telegram that does not contain any user data.
INTERROGATION	539	GQ, Counter Request
FBP	540	Fixed test bit pattern
CP16	541	2 byte time
CP24	542	3 byte time
CP56	543	7 byte time
DBCR	545	Counter value 6 Octet BCD
FBCR	546	8 Octet floating-point number

MODBUS


Transformation type	Integer	Description
UNDEFINED	560	undefined
INT16	561	16-bit integer signed
INT32	562	32-bit integer signed
INT64	571	64-bit integer signed
UINT16	563	16-bit integer unsigned
UINT32	564	32-bit integer unsigned
UINT64	574	64-bit integer unsigned
CHAR	565	Character
FLOAT	566	Floating-point value
BIT	567	Bit
BOOLEAN_AS _BYTE	568	Boolean as byte
STRING	569	Text
BLOB	570	Blob
DOUBLE	572	64 Bit IEEE 754 Floating-point number
FLOAT with timestamp	573	Floating-point number with time stamp
MOD10 SIZE 2	575	PLC specific transformation type MOD10 with a size of 2 registers.
MOD10 SIZE 3	576	PLC specific transformation type MOD10 with a size of 3 registers.
MOD10 SIZE 4	577	PLC specific transformation type MOD10 with a size of 4 registers.

OPC


Transformation type	Integer	Description
DEFAULT	0	Default
UNDEFINED	480	Undefined
INT16	481	16-bit integer signed
INT32	482	32-bit integer signed
UCHAR	483	Character unsigned
FLOAT32	484	32-bit float
FLOAT64	485	64-bit float
BOOL	486	Bool
STRING	487	String
UINT16	488	16-bit integer unsigned
UINT32	489	32-bit integer unsigned
TIME	490	Time
BITSTRING	491	Bit pattern

OPC UA


Transformation type	Integer	Description
DEFAULT	750	Default
BOOLEAN	751	Boolean
SBYTE	752	Short Byte
BYTE	753	Byte
INT16	754	16-bit Integer signed
UINT16	755	16-bit Integer unsigned
INT32	756	32-bit Integer signed
UINT32	757	32-bit Integer unsigned
INT64	758	64 Bit Integer signed
UINT64	759	64 Bit Integer unsigned
FLOAT	760	Floating-point value
DOUBLE	761	Floating-point value, double precision
STRING	762	String
DATETIME	763	Date & Time
GUID	764	Unique Identifier
BYTESTRING	765	Byte String
XMLELEMENT	766	XML Element
NODEID	767	Node ID
LOCALIZEDTEXT	768	Localized Text

RK512


Transformation type	Integer	Description
UNDEFINED	240	Undefined
BYTE	241	Byte
UBYTE	242	Unsigned byte
WORD	243	Word
UWORD	244	Unsigned word
DWORD	245	Double word
UDWORD	246	Double word unsigned
FLOAT	247	Float
BCD	248	2 byte BCD
BCD4	249	4 byte BCD
KC	250	Counter format
KT	251	Timer format
BIT	252	Bit
STRING	253	String
LBYTE	254	Lower byte of a word
RBYTE	255	Upper byte of a words

SBUS


Transformation type	Integer	Description
UNDEFINED	1001	Undefined
BOOLEAN	1002	16-bit Integer signed
INT32	1003	32-bit Integer signed
UINT32	1004	32-bit Integer unsigned
FLOAT	1005	Floating-point number
STRING	1006	String

SIM


Transformation type	Integer	Description
UNDEFINED	0	Undefined
BOOLEAN	1	Bit (bool value)
INT8	2	8-bit integer signed
INT16	3	16-bit integer signed
INT32	4	32-bit integer signed
UINT8	5	8-bit integer unsigned
UINT16	6	16-bit Integer unsigned
UINT32	7	32-bit Integer unsigned
FLOAT	8	Floating-point value
VISIBLE	9	Text
OCTET	10	Octet string
DATE	11	Date
TIME	12	Time
TIME DIFF	13	Time difference
BITSTRING	14	Bit string
REVERSE BITSTRING	15	Bit string in reversed bit order

SINAUT


Transformation type	Integer	Description
DEFAULT	720	Default
BIT	721	Bit
BIT32	722	32-bit
FLOAT32	723	32-bit Floating-point value
INT16	724	16-bit Integer
INT32	725	32-bit Integer
UINT28	726	28 Bit Integer unsigned

SNMP


Transformation type	Integer	Description
UNDEFINED	660	Undefined
INT32	661	32-bit integer signed
UINT32	662	32-bit integer unsigned
UINT64	663	64-bit integer unsigned
OID	664	Object Identifier (int-array or string)
OCTET	665	Octal number
DISPLAYSTRING	666	Octet string, c-style string 0-255, string representation, non printable characters ignored.
DATETIME	667	Octet string, length: 8 or 11
MACADDRESS	668	Octet string, length: 6
IPADDRESS	669	Octet string, length: 4
BITS	670	Bitstring (SNMP v2)
DISPLAYHEXSTRING	673	Octet, c-style string 0-255, hex representation

SSI


Transformation type	Integer	Description
UNDEFINED	40	Undefined
UINT32	41	32-bit integer unsigned
INT32	42	32-bit integer signed
TRAFO	43	Transformer tap position
FLOAT	44	Floating-point value
COMBVAL	45	Combination message
STRTRANSP	46	String with transparent data
SINGLEALARMS	47	16 individual messages
8DOUBLEIND	48	8 double messages
4DOUBLEIND	49	4 double messages
1DOUBLEIND	50	Individual data point message
BINARYCOMMAND	51	Command

S7


Transformation type	Integer	Description
UNDEFINED	700	Default
INT16	701	16-bit Integer signed
INT32	702	32-bit Integer signed
UINT16	703	16-bit Integer unsigned
BYTE	704	Byte
FLOAT	705	Floating-point value
BIT	706	Boolean
STRING	707	Text
UINT32	708	32-bit Integer unsigned
DATETIME	709	Date/Time variable (used for S7 300 and S7 400 models)
BLOB	710	Blob
BITSTRING	711	Bit pattern
TimeOfDay	713	Time
S5Time	714	Time for S5 compatibility
DATETIMELONG	718	Date/Time variable (used for S7 1200 models)
Int32WithQuality	719	32-Bit Integer signed with (optional) quality information
UInt32WithQuality	720	32-Bit Integer unsigned with (optional) quality information
FloatWithQuality	721	Floating-point value with (optional) quality information

S7Plus


Transformation type	Integer	Description
DEFAULT	1001	Default
BOOL	1002	Boolean
BYTE	1003	8-bit integer unsigned
WORD	1004	Bit field (16-bit)
DWORD	1005	Bit field (32-bit)
LWORD	1006	Bit field (64-bit)
USINT	1007	8-bit integer unsigned
UINT	1008	16-bit integer unsigned
UDINT	1009	32-bit integer unsigned
ULINT	1010	64-bit integer unsigned
SINT	1011	8-bit integer signed
INT	1012	16-bit integer signed
DINT	1013	32-bit integer signed
LINT	1014	64-bit integer signed
REAL	1015	32-bit float
LREAL	1016	64-bit float
DATE	1017	Date, number of days since 1.1.1970
DATETIME	1018	Date and time
TIME	1019	Time in milliseconds (32-bit), value range from -24d 20h 31m 23s 648ms to +24d 20h 31m 23s 647ms
TIME_OF_DAY	1020	Number of milliseconds since start of the day (32-bit)
LDATETIME	1021	Date and time
LTIME	1022	Time in nanoseconds (64-bit), value range from -106751d 23h 47m 16s 854ms 775us 808ns to +106751d 23h 47m 16s 854ms 775us 807ns
LTOD	1023	Number of milliseconds since start of the day (64-bit)
DTL	1024	12 Byte struct, value range from 1970-01-01-00:00:00.0 to 2554-12-31-23:59:59.999999999
S5TIME	1025	Time in milliseconds (16-bit), value range from 0h 0m 0s 0ms to 2h 46m 30s 0ms
STRING	1026	String
WSTRING	1027	String

"_address.._direction" peripheral address


CTRL constant	Int value	Description
DPATTR_ADDR_MODE_UNDEFINED	0	Undefined.
DPATTR_ADDR_MODE_OUTPUT	1	Standard output. This mode uses a group connection on address subindices. If the value of a subindex changes, the driver retrieves all values of all subindices in a hotlink and creates a telegram with these values for the periphery. In other words, the driver always receives all values when one of the sub-indices changes.
DPATTR_ADDR_MODE_INPUT_SPONT	2	Input for spontaneous data
DPATTR_ADDR_MODE_INPUT_SQUERY	3	Input for single queries
DPATTR_ADDR_MODE_INPUT_POLL	4	Input for polling (cyclic query).
DPATTR_ADDR_MODE_OUTPUT_SINGLE	5	Output with single connection on address subindices. If a subindex changes, the driver only receives the value of the changed subindex in a hotlink. This means that if the message consists of several subindeces, the data of the missing subindeces is allocated 0. If only one subindex exists for an address, the address modes OUTPUT and OUTPUT_SINGLE have the same behavior.
DPATTR_ADDR_MODE_IO_SPONT	6	Input/output for spontaneous data
DPATTR_ADDR_MODE_IO_POLL	7	Input/output for polling (cyclic query).
DPATTR_ADDR_MODE_IO_SQUERY	8	Input/output for single queries
DPATTR_ADDR_MODE_AM_ALERT	9	Hardware alert handling. External alerts are triggered via this address.
DPATTR_ADDR_MODE_INPUT_ON_DEMAND	10	Currently not in use.
DPATTR_ADDR_MODE_INPUT_CYCLIC_ON_USE	11	Input, Value is polled only if a query (e.g. dpConnect() oder dpQueryConnect() ) exists for the element.
DPATTR_ADDR_MODE_IO_ON_DEMAND	12	Currently not in use.
DPATTR_ADDR_MODE_IO_CYCLIC_ON_USE	13	Input/output, Value is polled only if a query (e.g. dpConnect() oder dpQueryConnect() ) exists for the element.
DPATTR_ADDR_MODE_INPUT_SPONT_ON_USE	14	Input, address is only subscribed for transmission if a query (e.g. dpConnect() oder dpQueryConnect() ) exists for the element.
DPATTR_ADDR_MODE_IO_SPONT_ON_USE	15	Input/output, address is only subscribed for transmission if a query (e.g. dpConnect() oder dpQueryConnect() ) exists for the element.
DPATTR_ADDR_MODE_INTERNAL	32	Obsolete. Use the attribute _internal instead.
DPATTR_ADDR_MODE_LOW_LEVEL_FLAG	64	Obsolete. Use the attribute _lowlevel instead.

Example

Adds an "_address" config, which can be used to configure the parameters for the peripheral address of a DPE. The example also sets the driver type to "ABB".

main()
{
  dpSetWait("TestDP_1.element:_address.._type",
  DPCONFIG_PERIPH_ADDR_MAIN,
  "TestDP_1.element:_address.._drv_ident","ABB");
}

For more details on the _address config, see chapter Module PARA - _address (peripheral address).