Details zum PROFIsafe-Treiber
Einschränkungen
PROFINET
max. 256 IO-Devices pro IO-Controller
max. 254 Byte pro Subslot (Transferbereich)
max. 64 Subslots
PROFIsafe
max. 32767 F-Adressen pro IO-Controller
max. 8 Byte pro Subslot (Transferbereich)
max. 32 Subslots
Debug-Flags
Um mögliche Fehlerquellen bei einem laufenden Treiber zu erkennen, stehen folgende Debug-Flags zur Verfügung.
| Debug Level | Beschreibung |
|---|---|
| 25 (DBG_DRV_USR1) | Informationen zum PROFINET-Datenaustausch |
| 26 (DBG_DRV_USR2) | Informationen zum PROFIsafe-Datenaustausch |
| 27 (DBG_DRV_USR3) | Informationen zur Konfiguration und Callbacks |
| rec | Informationen zum Austausch von PROFINET-Datensätzen (betrifft Konfiguration & Statusinformationen) |
HARD_FAIL / SAFECONDITION
Bei einem Fehler, der zu einem HARD_FAIL führt, wird
- der Treiber gestoppt
- das Invalidbit aller Eingangs-Datenpunktelemente gesetzt
- der Status am internen Datenpunktelment .Profisafe.State auf 5 (Fehler) gesetzt.
Dieser Status ist die SAFECONDITION des Treibers.
Fehlermeldungen
| Fehlercode | Beschreibung |
|---|---|
| 0x010 | IRT data may be inconsistent |
| 0x011 | No submodules to be updated |
| 0x012 | Data was written with local state PNIO_S_BAD because not all components of splitted module have local state PNIO_S_GOOD |
| 0x101 | Parameter handle is illegal |
| 0x102 | Parameter buffer is NULL pointer |
| 0x103 | Parameter length is wrong |
| 0x104 | Parameter address is wrong |
| 0x105 | Parameter remote state is NULL pointer |
| 0x106 | Parameter cbf is illegal |
| 0x107 | Parameter type has no valid value |
| 0x108 | Parameter ExtPar has no valid value |
| 0x109 | Parameter PNIO_ADDR::IODataType is wrong |
| 0x10A | Parameter CpIndex is wrong, probably driver is not loaded |
| 0x10B | Parameter IOlocState has no valid value |
| 0x10C | Parameter RecordIndex has no valid value |
| 0x10D | Parameter timeout has no valid value |
| 0x10E | Parameter annotation has no valid value |
| 0x10F | Parameter state has no valid value |
| 0x110 | Parameter pCbf has no valid value |
| 0x111 | Parameter MaxAR has no valid value |
| 0x112 | Parameter AccessType has no valid value |
| 0x113 | An invalid pointer was passed |
| 0x114 | An invalid argument was passed |
| 0x115 | Wrong measuer number in cycle statistics, must be -1 (actual measured up to 49 |
| 0x116 | Wrong Offset for cycle info buffer (must be 0 to 19) |
| 0x117 | Address used by io router |
| 0x201 | Unknown handle |
| 0x202 | Maximal number of opens reached, close unused applications |
| 0x203 | Fatal error, reboot your system |
| 0x204 | Parameter mode has no valid value |
| 0x205 | Register OPFAULT callback before register STARTOP callback |
| 0x206 | Register NEWCYCLE callback before register STARTOP callback |
| 0x207 | Network protocol not available, check card configuration |
| 0x208 | Pnio stack not available, try again later |
| 0x301 | Device data not available, because device because device is not connected to controller |
| 0x302 | Fatal error, no more operation system resources available |
| 0x303 | Action was already performed |
| 0x304 | No configuration for this index available |
| 0x305 | PNIO_set_mode not allowed, use PNIO_CEP_MODE_CTRL by PNIO_controller_open |
| 0x306 | PNIO_device_activate not allowed, use PNIO_CEP_MODE_CTRL by PNIO_controller_open |
| 0x307 | License server not running, check your installation |
| 0x308 | Wrong length value |
| 0x309 | Wrong calling sequence |
| 0x30A | Invalid configuration, check your configuration |
| 0x30B | Address unknown in configuration, check your configuration |
| 0x30C | No resource too many requests been processed |
| 0x30D | Configuration update is in progress or CP is in STOP state, try again later |
| 0x30E | No communication with firmware, reset cp or try again later |
| 0x30F | No synchronous function allowed, use PNIO_CEP_SYNC_MODE by PNIO_controller_open or PNIO_device_open |
| 0x310 | Interface-submodule cannot be removed because it is owned by an AR |
| 0x311 | Failed to start thread, probably by lack of pthread resources |
| 0x312 | Failed to start realtime thread, probably you need root capability to do it |
| 0x313 | Failed to ioctl driver, probably API version mismatch |
| 0x314 | Exception occurred, save exception info and reset cp |
| 0x315 | No cycle data available |
| 0x316 | Request belongs to an old session |
| 0x317 | Wrong format of alarm data |
| 0x318 | Operation was aborted |
| 0x319 | Data is corrupted or has wrong format |
| 0x31A | Error by flash operations |
| 0x31B | Wrong length of request block at firmware interface, firmware not compatible to host sw |
| 0x31C | Reset request was sent to firmware, but firmware startup cannot be verified |
| 0x31D | Failed to start thread for handling asynchronous buffer exchange |
| 0x31E | Pnio lib in host could not attach to PPA register set |
| 0x31F | No callback registered |
| 0x320 | Update time is out of expected range |
| 0x321 | Update of firmware requires a host restart |
| 0x323 | Location format invalid |
| 0x324 | Location level invalid |
| 0x325 | Annotation too large |
| 0x326 | Order ID too large |
| 0x327 | Both hardware versions set |
| 0x328 | Hardware version long too large |
| 0x329 | Both software versions set |
| 0x32A | Software version long too large |
| 0x32B | Serial number too large |
